Simrad PI DEPTH Spécifications Page 237
- Page / 268
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Sensor test procedures
225
857-164636 / Rev.A
(4) = A second start flash: This signals that the second
digit of the channel number is next.
(5) = None to nine short flashes: The number of short
flashes signifies the second digit of the configured
channel number.
3 Using a multimeter, check the DC current between the
negative charging lug (A) and the water detector (B).
- With the initial sea water switch and a a fully charged
battery, the current should not exceed 150 µA.
- With a redesigned sea water switch (sacrificial bolt)
and a a fully charged battery, the current should not
exceed 67 µA.
- If you measure 0 µA, check the fuse on your
multimeter.
Testing on land
1 Connect the P I Service Hydrophone to the PI Operator
Unit.
2 Place the sensor on a level surface with its “domed top”
pointing towar ds the test hydrophone approximately five
meters away.
3 Use the Status display on the PI to monitor the sensor’s
signal strength.
- If the interference filter is on, the spectrum displayed
should be relatively flat (approximately 25 dB,
interference filter set at level 9) with a peak detected in
the configured channel.
4 Check that the bottom contact symbol on the P I is
“touching the bottom” when the detector wire is not pulled
out.
5 Pull out the detector wire, and check that the sensor
presentation changes.
Testing in water
1 Disconnect the PI Service hydrophone, and reconnect the
vessel’s normal hull mounted hydrophone.
2 Switch off the vessel’s echo sounders, sonars and other
hydroacoustical equipment to avoid interference.
3 Lower the sensor over the side of the vessel.
- Note that the weight of the sensor in water
(approximately 1.4 kg) may not provide sufficient
resistance to trigger the sensor’s bottom contact
function when the detector wire is pulled. Apply extra
weight if required.
- Operator manual 1
- Catch monitoring system 3
- About this document 4
- Sections 5
- 12 Sensor test procedures 6
- 13 Technical specifications 6
- Simrad PI32 10
- INTRODUCTION 13
- SYSTEM DESCRIPTION 14
- System diagram 15
- Operator Unit 16
- Sensor overview 18
- Battery chargers 19
- GETTING STARTED 20
- Power on 21
- Power off 21
- Page 1: Echo sounder 22
- Page 2: Numeric display 22
- Page 3: Graphic display 22
- Page 4: Navigation display 22
- Leafing through the pages 23
- Other display presentations 23
- Introduction to the main menu 24
- Introduction to the keypad 25
- Introducing the sensors 27
- Depth: How deep can you go? 29
- Rip: Check for damages! 30
- APPLICATION EXAMPLES 32
- Purse seine 33
- Danish seine 34
- Bottom trawl 35
- Pelagic trawl 36
- Echo sounder 37
- Graphic display 38
- DISPLAY PRESENTATIONS 39
- Numeric display 40
- Depth presentation 43
- Height presentation 44
- Spread presentation 45
- Surface temperature 49
- Status display 50
- → Receiver setup, page 174 51
- Echo sounder display 52
- Bottom expansion 53
- Navigation display 55
- Position display 56
- OPERATIONAL PROCEDURES 57
- → Numeric display, page 28 59
- How to set up the sensors 60
- Predefined settings 61
- How to use the sensors 64
- How to test the sensors 66
- How to define sensor offsets 68
- MENU Exit 72
- GAIN- GAIN+ 72
- (CD11105C) 72
- → Twin Spread, page 128 73
- → Trawl info, page 182 73
- Howtoviewechosounderdata 75
- How to set up marker lines 76
- Depth and Height marker lines 77
- Spread marker line 77
- → Graphic setup, page 160 78
- Access to the parameters 80
- Set up the parameters 80
- Ping to ping filter 82
- Colour threshold 82
- Signal threshold 82
- Depth grid 82
- Standard mode 84
- Phased range mode 84
- Activate A-Scope 88
- De-activate A-Scope 88
- How to define alarm limits 89
- Surface temperature alarm 90
- Clearance alarms 90
- How to select menu language 92
- → Page setup, page 171 93
- PRACTICAL USE OF THE SENSORS 95
- PI Bottom Contact sensor 99
- Bottom Contact presentatio n 100
- Sensor configuration 100
- System configuration 101
- Mounting 101
- 857-164636 / Rev.A 102
- PS Bottom Contact sensor 103
- PI Catch sensor 107
- Presentation 108
- PS Catch sensor 112
- Catch presentation 113
- PI Depth sensor 116
- Numerical presentation 117
- PS Depth sensor 121
- PI Height sensor 126
- Daily operation 127
- PI Rip sensor 130
- Numeric presentation 131
- PI Spread and Remote sensors 135
- Installation principle 138
- Sacrificial water switch 139
- PI Twin Spread 140
- Main parts 141
- PI Temperature sensor 145
- Temperature presentation 147
- PS Temperature sensor 151
- SENSOR CHARGERS 156
- PI Charger 157
- PS30 Charger 159
- General guidelines 160
- Battery depleted frequently 160
- Typical sensor (PI Depth) 160
- MENU SYSTEM 161
- The main menu 162
- Menu system 163
- REFERENCES 164
- Depth calibration 165
- Echo presentation setup 166
- Echo sounder setup 169
- Related topics 170
- Factory presets 171
- Graphic setup 172
- → Sensor setup, page 179 173
- → Numeric setup, page 169 173
- Interface setup NMEA 174
- Applicable telegram formats 177
- Interface setup remote/alarm 179
- Navigation setup 180
- Numeric setup 181
- Offset adjust 182
- Page setup 183
- Palette setup 184
- Position display setup 185
- Receiver setup 186
- Sensor alarms 189
- Sensor setup 191
- Speed setup 192
- Surface temperature setup 193
- Trawl info setup 194
- Units setup 195
- PI CONFIGURATOR 196
- Basic information 197
- Available equipment 198
- About sensor configuration 199
- Changing the update rate 200
- Main dialogue description 201
- Operational procedures 203
- Software installation 204
- How to interface the sensor 205
- References 210
- Communication P o rt Setup 212
- Operation 212
- Configure Sensor 213
- Factory Default 216
- Language 218
- LED Control 219
- Message field 220
- PI Configurator 221
- Ping control 222
- Read Sensor Data 224
- Sensor Type 226
- Show Channel At Startup 228
- Examples 229
- Terminate Communication 230
- Maintenance 231
- Making a programming cable 233
- Troubleshooting 234
- SENSOR TEST PROCEDURES 235
- Bottom Contact test procedure 236
- Testing on land 237
- Testing in water 237
- Catch sensor, test procedure 239
- Depth sensor, test procedure 242
- PI32 Calibration procedure 244
- PI44 Calibration procedure 244
- Height sensor, test procedure 245
- Tools and equipment required 248
- TECHNICAL SPECIFICATIONS 255
- PI Bottom Contact 256
- PI Catch & PI Rip 256
- PI Depth 257
- PI Height 258
- PI Spread & Remote 258
- PI Temperature 259
- - To 70% capacity: 1 hour 260
- - To 100% capacity: 4 hours 260
- - To 100% capacity: 16 hours 260
- E 2005 Simrad AS 268
- ISBN 82-8066-059-3 268
Produits connexes et manuels pour Non Simrad PI DEPTH
Non Simrad FS25 Guide de l'utilisateur
(108 pages)
(108 pages)
Non Simrad SP60 - REV D Manuel d'utilisateur
(44 pages)
(44 pages)
Non Simrad ER60 - REV B Informations techniques
(256 pages)
(256 pages)
Non Simrad SH90 - REV B Spécifications
(2 pages)
(2 pages)
Non Simrad SH80 - REV C Manuel d'installation
(214 pages)
(214 pages)
Non Simrad ITI Manuel d'utilisateur
(36 pages)
(36 pages)
Non Simrad SP60 - REV D Manuel d'installation
(178 pages)
(178 pages)
Non Simrad EQ 55 Informations techniques
(154 pages)
(154 pages)
Non Simrad SH80 - REV C Manuel d'installation
(200 pages)
(200 pages)
Non Simrad RS90 Manuel d'utilisateur
(24 pages)
(24 pages)
Sharp SJ-F78PESL manuales
Manuales del propietario y guías del usuario para Para Casa Sharp SJ-F78PESL.
Ofrecemos 2 manuales en pdf Sharp SJ-F78PESL para descargar gratis por tipos de documentos: Manual de usuario
Sharp SJ-F78PESL Manual de usuario (156 paginas)
Marca: Sharp | Categoria: For Home | Tamaño: 27.74 MB |
Tabla de contenidos
Sharp SJ-F78PESL Manual de usuario (2 paginas)
Marca: Sharp | Categoria: For Home | Tamaño: 0.65 MB |
Tabla de contenidos
Más productos y manuales para Para Casa Sharp
| Modelos | Tipo de documento |
|---|---|
| SJ-300VBE |
Manual de usuario
Sharp SJ-300VBE Manuale d'uso,
2 paginas
|
| LC-50LE760E |
Manual de usuario
Sharp LC-50LE760E Manuale d'uso,
40 paginas
|
| LC-60LE857E |
Manual de usuario
Sharp LC-60LE857E Manuale d'uso,
95 paginas
|
| AY-XP24LR - AE-X24LR |
Manual de usuario
Sharp AY-XP24LR - AE-X24LR Manuale d'uso,
2 paginas
|
| SJ-WS320TS |
Manual de usuario
Sharp SJ-WS320TS Manuale d'uso,
2 paginas
|
| SJ-FS810VSL |
Manual de usuario
Sharp SJ-FS810VSL Manuale d'uso,
2 paginas
|
| LC-46LD264E |
Manual de usuario
Sharp LC-46LD264E Manuale d'uso,
2 paginas
|
| AN-WUD630 |
Manual de usuario
Sharp AN-WUD630 Manuale d'uso,
1 paginas
|
| R-23AM |
Manual de usuario
Sharp R-23AM Manuale d'uso,
2 paginas
|
| LC-60UD20E |
Manual de usuario
Sharp LC-60UD20E Manuale d'uso,
89 paginas
|
| LC-32LD164E |
Manual de usuario
Sharp LC-32LD164E Manuale d'uso,
2 paginas
|
| AY-XPC18LR - AE-X18LR |
Manual de usuario
Sharp AY-XPC18LR - AE-X18LR Manuale d'uso,
2 paginas
|
| R-922STWE |
Manual de usuario
Sharp R-922STWE User Manual,
266 paginas
|
| AY-XPC12RR-AE-X12RR |
Manual de usuario
Sharp AY-XPC12RR-AE-X12RR Manuale d'uso,
2 paginas
|
| LC-60LE857E |
Manual de usuario
Sharp LC-60LE857E Manuale d'uso,
2 paginas
|
| LC-60UD20E |
Manual de usuario
Sharp LC-60UD20E Manuale d'uso,
2 paginas
|
| LC-80LE657E |
Manual de usuario
Sharp LC-80LE657E Manuale d'uso,
95 paginas
|
| AY-X9RSR-AE-X9RSR |
Manual de usuario
Sharp AY-X9RSR-AE-X9RSR Manuale d'uso,
2 paginas
|
| SJ-F800SPBK |
Manual de usuario
Sharp SJ-F800SPBK Manuale d'uso,
2 paginas
|
| SJ-PD691SB |
Manual de usuario
Sharp SJ-PD691SB Manuale d'uso,
2 paginas
|
© 2020, manymanuals.fr. Tous droits réservés | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels